Replacing a side lamp on a Largus – All about Lada Granta

What kind of bulbs are in the headlights?

Low and high beam lamp - H4, power 12V, 60/55W;
Bulb dimensions - W5W, power 5W;
Front turn signal lamp - PY21W;
Fog lamps - H11, power 12V, 55W.

Low and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To gain access to the left headlight unit, you must remove the battery.

Turn the lid counterclockwise;
Remove the cover by releasing the latch.

Remove the block with wires by unclipping the lock;
Remove the rubber cover by prying it off by the edge.

Unscrew the lamp clamp to the side;
Remove the headlight bulb.

Installing a new lamp in the Largus headlight is carried out in the reverse order. You need to hold the lamp by the base; it is not recommended to touch the bulb with your fingers. If necessary, wipe the flask with a microfiber cloth that does not leave lint. The process of replacing the H4 lamp is also shown in the video:

Read more: Conditions for the use of firearms by police officers

Lada Largus low beam light bulb

A note about what kind of lighting lamps are installed in the Largus headlights; which of them are low/high beam, and which are responsible for the side lights. How to change lamps yourself. How much do originals and analogues cost in Yaroslavl?

Good day, future and aspiring gentlemen Largusovod!

On Largus, the low/high beam and headlight lamps often burn out. At least for 70 thousand I have already changed it five times on each side.

The following light bulbs were installed on my car:

1. Low/high beam: halogen, Osram H4 12v 60/55w. (art. 64193). Price from 109 rub.

There are many analogues. Here are some of them:

370 rub. General Electric (34454)

117 rub. Valeo (032007)

2. Front dimensions: halogen baseless 12V Osram (art. 2825). Price from 17 rub.

26 rub. Lynx (L12805)

9 rub. Fortluft (2825)

3. Rear dimensions: two-pin with filament, base BAY15D. Beacon 12V P21/5W.

from 56 rub. Fortluft (7528)

They burn out less often. I changed it only once in the right lamp. This is what she looks like:

How to replace headlight bulbs

1. First, remove the protective cover. It turns a little, then a small latch is released.

2. The block with wires is removed.

3. Remove the rubber protective sleeve.

4. The lamp is pressed U -shaped clamp. It needs to be pulled to the side and back.

5. Take out the lamp. Remember its orientation. Two teeth at the bottom, one at the top. And if you look at it from the side of the headlight, the inscription (marking) will be on top.

6. Install a new lamp. You should not take it with your bare hands, as greasy marks from the pores will remain on the bulb and the lamp will fail faster. This applies to all halogen lamps. It is better to hold it by the plinth or use a microfiber cloth.

7. Assembly is carried out in reverse order. First the clamping clamp, then the rubber bushing and finally the top cover.

How to replace front markers

There isn't much action here. The main thing is to get to the cartridge and turn it 90 degrees. The most inconvenient thing to change is the battery side. Not enough space. If your hand is large, it is better to remove it.

Thus, the procedure is as follows:

Found a cartridge
They turned it over and took it out
Removed the lamp
It is better to wear gloves when installing a new lamp into the socket.
Then we insert the cartridge back into the headlight and rotate it 90 degrees.

PTF lamp (fog lamp)

There is no access to the lamp from the engine compartment, so replacement is made from below.

Remove the fender liner by removing the screws;
Disconnect the block from the lamp by pressing the lock;
Remove the lamp by turning it a third of a turn counterclockwise.

Install the lamp in the reverse order.

Attention! In practice, replacing lamps in a Largus headlight is much easier. In other words, it is not at all necessary to remove the battery and fender liners (lockers). If you get the hang of it, you can access all the headlight bulbs from the engine compartment.

Let us remind you that other operating and repair instructions for Lada Largus are in this category. It is convenient to find the answer to your question based on the content.

During operation of the vehicle, the headlight bulbs may burn out. If you decide to replace them not at the dealer, but yourself, we recommend that you first study the instructions. The fact is that on the Lada Largus the lamps in the headlights change with some features, which we will discuss later.

What kind of bulbs are in the headlights?

Low and high beam lamp - H4, power 12V, 60/55W;
Bulb dimensions - W5W, power 5W;
Front turn signal lamp - PY21W;
Fog lamps - H11, power 12V, 55W.

Low and high beam lamp - H4, power 12V, 60/55W

Bulb dimensions - W5W, power 5W

Front turn signal lamp - PY21W

Fog lamps - H11, power 12V, 55W

Low and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To gain access to the left headlight unit, you must remove the battery.

Turn the lid counterclockwise;
Remove the cover by releasing the latch.

replacing low and high beam lamps Lada Largus

Remove the block with wires by unclipping the lock;
Remove the rubber cover by prying it off by the edge.

replacing low and high beam lamps Lada Largus

Unscrew the lamp clamp to the side;
Remove the headlight bulb.

replacing low and high beam lamps Lada Largus

Side light bulb

There is no access to the lamp from the engine compartment, so replacement is made from below.

Remove the fender liner by removing the screws;
Remove the lamp socket by turning it clockwise (for the right one - counterclockwise);
Remove the baseless lamp from the socket.

remove the fender liner Lada Largus

replacing the side light bulb on Lada Largus

Install the new lamp in the reverse order.

Turn signal lamp

There is no access to the lamp from the engine compartment, so replacement is made from below.

Remove the fender liner by removing the screws;
Remove the lamp socket by turning it counterclockwise;
Remove the lamp by pressing and then turning it counterclockwise.

Removing the fender liner Lada Largus

replacing turn signal lamp Lada Largus

Install the new lamp in the reverse order.

PTF lamp (fog lamp)

There is no access to the lamp from the engine compartment, so replacement is made from below.

Remove the fender liner by removing the screws;
Disconnect the block from the lamp by pressing the lock;
Remove the lamp by turning it a third of a turn counterclockwise.

Removing fender liners Lada Largus

replacing lamps in PTF Lada Largus

Install the lamp in the reverse order.

Attention! In practice, replacing lamps in a Largus headlight is much easier. In other words, it is not at all necessary to remove the battery and fender liners (lockers). If you get the hang of it, you can access all the headlight bulbs from the engine compartment.

Let us remind you that other operating and repair instructions for Lada Largus are in this category. Find the answer to your question conveniently by content.

The headlights installed on the Lada Largus are exactly the same as on the Renault Logan. Therefore, all the lamps in their headlights are exactly the same. Unlike the new generation Renault Logan, Largus has ordinary lamps with sockets h4, h11 and others. For reference, the new Logan has PSX24 lamps installed in the fog lamps, the price of which is from 500 rubles and a power of 24 watts.

Troubleshooting Some Problems

If, after replacing the lamp, the low beam on the Lada Largus still does not light up, the cause of the malfunction may be a blown fuse. Replacing them is even easier than the paws, since they are located in the cabin, on the left side of the steering column.

Two fuses are responsible for the low beam:

F9 – left headlight.
F10 – right headlight.

Note! Even if the fuse is not visually damaged, a new one should be installed in its place.

Often the cause of the malfunction is poor contacts of the fuse terminals. In this case, you just need to clean them.

It should be noted that there is no low beam relay on the Lada Largus, therefore, if replacing the fuses did not produce results, all that remains is to check the contacts in the headlight itself, which could have burned out or oxidized.

Often the light goes out due to poor contact of the machine ground wire. In this case, the problem is also solved by thoroughly cleaning the contact. If it was not possible to restore the light, you need to contact a service center for help.

Here, perhaps, are all the instructions for correcting the most common VAZ wiring faults.

Cost of lamps

All of the above lamps can be purchased at almost any auto store. For example, a Philips H4 Premium +30 low beam lamp installed from the factory costs about 120-150 rubles. PTF lamp H11 Philips Eco Vision about 500-600 rubles per joke. All other lamps cost no more than 40-50 rubles.

Low beam bulbs on a Lada Largus car are a short-lived element, so sooner or later car owners will definitely have to deal with replacing them. For beginners, this task usually raises many questions. Therefore, below we will look at how to choose the right one and how to change the low beam bulb on Largus.

Choice

Currently on the market you can find such lamps from a variety of manufacturers, among which are the following:

In addition, domestic Mayak light bulbs have recently proven themselves to be quite good. Their advantages include not only low price, but good quality.

Of course, when choosing lamps you need to pay attention not only to the brand, but also to the following characteristics of the lighting element:

However, it should be noted that such light illuminates the road well only in dry weather. In fog or rain, ordinary lamps are preferable.

Note! To install xenon and halogen lamps, you should contact a service center for help, since this work requires the installation of additional equipment and changes to the software. Accordingly, the installation of such lighting is quite expensive.

Thus, each driver can choose the most suitable light bulb, taking into account his own financial capabilities and the conditions in which the car will be operated.

Replacing the low beam lamp on a Lada Largus is carried out in the following order:

Next, you need to install a new light bulb in place. It is better to do this work with gloves so as not to touch the glass flask with your own hands. The fact is that traces of fat can lead to rapid burnout of the lamp.
Then you need to fix the base with a spring clip, put the block on the contacts and then install the plug in place.
At the end of the work, you should connect the battery and check the operation of the headlights.

This completes the replacement of the low beam lamp in Largus. As we can see, this operation is carried out extremely simply.

F9 - left headlight.
F10 - right headlight.

Often the cause of the malfunction is poor contacts of the fuse terminals. In this case, you just need to clean them.

Replacing a light bulb

Choice

First of all, it should be said that the low beam lamp for the Lada Largus uses a halogen H4 standard, i.e. contains two threads and is responsible not only for near, but also for distant lighting.

Currently on the market you can find such lamps from a variety of manufacturers, among which are the following:

In addition, domestic Mayak light bulbs have recently proven themselves to be quite good. Their advantages include not only low price, but good quality.

Advice! It is advisable to purchase light bulbs in specialized stores, since recently a lot of counterfeit products from China have appeared that quickly fail or produce poor-quality light.

Of course, when choosing lamps you need to pay attention not only to the brand, but also to the following characteristics of the lighting element:

Characteristics	Optimal parameters
Brightness (light beam power)	Up to 1550 lm
Lifetime	Up to 1500 hours
Power	45-60 W

Standard halogens provide an unnatural yellowish glow. However, recently light bulbs have appeared with a bluish glow. People call them pseudo-xenon.

However, it should be noted that such light illuminates the road well only in dry weather. In fog or rain, ordinary lamps are preferable.

Moreover, in bad weather, even the expensive “xenon” and “LEDs” are inferior to the latter, the power of the light beam is one and a half to two times more powerful than that of halogen bulbs. This is due to the fact that the light of these elements has insufficient penetrating power.

Note! To install xenon and halogen lamps, you should contact a service center for help, since this work requires the installation of additional equipment and changes to the software. Accordingly, the installation of such lighting is quite expensive.

Thus, each driver can choose the most suitable light bulb, taking into account his own financial capabilities and the conditions in which the car will be operated.

Replacement procedure

Replacing the low beam lamp on a Lada Largus is carried out in the following order:

Work should begin by disconnecting the terminal from the battery.
Then you need to remove the plug from the back of the headlight. To do this you need to turn it slightly.
After this, you should disconnect the block from the contacts by pulling it by the body.
Next, you need to remove the spring retainer from the grooves with your finger. After this, the bulb is easy to remove from the headlight, since nothing else holds it.

Next, you need to install a new light bulb in place. It is better to do this work with gloves so as not to touch the glass flask with your own hands. The fact is that traces of fat can lead to rapid burnout of the lamp.
Then you need to fix the base with a spring clip, put the block on the contacts and then install the plug in place.
At the end of the work, you should connect the battery and check the operation of the headlights.

Advice! It is advisable to change the bulbs in two headlights at once to ensure that they glow equally, and also to avoid the second bulb burning out, which can happen at the most inopportune moment.

This completes the replacement of the low beam lamp in Largus. As we can see, this operation is carried out extremely simply.

Conclusion

You can get additional useful information on the discussed topic from the video in this article.

What kind of bulbs are in the headlights?

Low and high beam lamp - H4, power 12V, 60/55W;
Bulb dimensions - W5W, power 5W;
Front turn signal lamp - PY21W;
Fog lamps - H11, power 12V, 55W.

Low and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To gain access to the left headlight unit, you must remove the battery.

Turn the lid counterclockwise;
Remove the cover by releasing the latch.

Remove the block with wires by unclipping the lock;
Remove the rubber cover by prying it off by the edge.

Unscrew the lamp clamp to the side;
Remove the headlight bulb.

How to remove a low beam lamp

Removing the low beam lamp on the Lada Largus occurs as follows:

Disconnect the on-board power supply.
First, disconnect the terminals from the battery.
Then remove the plug from the back of the headlight. So that you can remove it, simply turn it slightly counterclockwise, releasing the lock.
Next, disconnect the block from the contacts. Simply pull it by the body and release the latch.
Remove the rubber cover by prying it off.
Remove the spring clip from the grooves.

Now there is nothing holding the lamp, and you can easily remove it.

PTF lamp (fog lamp)

There is no access to the lamp from the engine compartment, so replacement is made from below.

Remove the fender liner by removing the screws;
Disconnect the block from the lamp by pressing the lock;
Remove the lamp by turning it a third of a turn counterclockwise.

Install the lamp in the reverse order.

Let us remind you that other operating and repair instructions for Lada Largus are in this category. It is convenient to find the answer to your question based on the content.

Lada Largus lamp base

1 Low and high beam lamp - H4 halogen lamp; power 60/55 watts. Cylindrical in shape, with three electrical contacts. Has two filaments.

2 Lamp front fog lights - H11 halogen lamp with a power of 55 watts. L-shaped lamp with a plastic base, with two contacts.

3 Taillight and brake signal lamp - two-pin incandescent lamp with a metal base P21/5W, power 21/5 watts.

4 Reversing and turn signal lamp - single-pin incandescent lamp PY21W, 21 watt.

5 Front turn lamp - yellow single-pin incandescent lamp PY21W, 21 watts.

6 Turn signal lamp - baseless single-pin lamp W5W yellow, 5 watts.

7 The license plate, trunk, and front marker lamp is a small single-contact W5W lamp with a power of 5 watts.

8 The stove control lamp is a small baseless C3W lamp with a power of 3 watts.

The best n4 lamps for Largus

Lada Largus has never been one of the expensive and premium cars. But despite the lack of it, there is a fairly high demand for it and it is in demand. Therefore, it will be useful for owners of this car to know which lamps are best installed on this car.

We can recommend lamps for low and high beam headlights from such manufacturers as: Osram Night Breaker, Philips X-Treme Vision, Koito Whitebeam

Which low beam lamp is suitable for Largus?

60/55 H4 lamps are installed at the factory:

60/55 is the power of low beam (55) and high beam (60) in watts,
H4 - base type.

Please note that the same bulb is used for low and high beam.

Quick comparison

Model	Peculiarities	Rating	Link
Philips X-treme Vision	the brightest, give white light	★★★★★	Buy
Philips LongLife EcoVision	inexpensive, extended service life	★★★★✩	Buy
Bosch Pure Light	extended service life	★★★★✩	Buy
Osram Original Line	good lighting area	★★★★✩	Buy

Philips X-treme Vision - the brightest light bulbs

Features declared by the manufacturer:

bright white light,
increase the lighting area in front of the car by 45 m,
high quality quartz glass.

One of the highest brightness levels and incredible comfort in the dark.

The package contains two lamps.

Country of origin: Poland.

What we like most: White bright light, increased illumination area.

Replacing the left low beam lamp Largus

To replace the headlight bulb on the left side, you must remove the battery. After removing the battery, replacing it is quite easy and quick.

1 You need to remove the plastic protective cap by simply prying it off.

2 Next, carefully remove the electrical connector from the headlight lamp and move it to the side so that it does not interfere with us.

3 Then remove the rubber boot, which prevents dirt and dust from entering the headlight unit.

4 To complete the removal of the lamp, we need to remove the metal retainer that holds the lamp.

5 Remove the old lamp and replace it with a new one.

Assembly is carried out in reverse order. The lamp is replaced in the same way on the right headlight, with the exception of the need to remove the battery. But if you have any questions, write them in the comments.

Replacing the low beam lamp of Lada Largus (VAZ Largus)

Car headlights are designed to provide a full view of the road at night. The proper condition of all lighting sources on the car is a necessary condition for safety while driving. Traffic regulations set very strict requirements for the serviceability of headlights. A driver who does not comply with them is subject to a fine.

To avoid troubles with the car inspection, the car owner is obliged to regularly inspect the lights on his car and, if defects or breakdowns are detected, promptly take measures to eliminate them.

Headlights on Lada Largus may have the following types of problems:

burnt out lamps;
broken lamps;
cracks on the surface of the optics;
dimming of lights;
incorrect formation of the light beam, etc.

The reasons for these problems may vary. Clouding of the optics is caused by the matting effect of dust particles in the oncoming air flow; cracks and broken lamps are usually the result of a collision with an obstacle while driving. Scratches on the surface of the optics can be the result of driving on roads with bushes and trees with spreading branches growing on the sides.

Driving with headlights that have any of the above factors is unacceptable. To carry out repairs, you can contact a service station, where qualified technicians will provide you with the required assistance. But car service costs money - not all vehicle owners are ready to incur financial expenses.

If you want to avoid spending money, try doing it yourself. On Lada Largus cars, replacing lamps and lights does not cause any particular difficulties. And use the information you glean from this article as a guide.

Changing lamps

First, let's look at how to replace the low beam bulb and replace the high beam bulb on the Lada Largus. Headlights on Lada Largus use one H4 lamp with a voltage of 12 V and a power of 60/55 W for low and high beam. Therefore, replacing the low beam bulb on a Lada Largus will automatically mean replacing the high beam bulb.

While working, follow the following algorithm:

To access the left light, you will need to remove the battery.
Turn the lantern cover counterclockwise.
Release the holder and remove the cover.
Release another holder to remove the cable block.
Hook the rubber cap on the edge and open it.
Move the light bulb holder aside and remove it.

Install the new product and follow the procedure in reverse order.
As in other cars, in Lada Largus lamps are replaced on both sides, even if one fails. This is explained by the need for complete symmetry in road lighting. Therefore, do the same procedure on the right side.

Remember that you must hold the light bulb by the base - touching the bulb with your hands is strictly prohibited. Otherwise, the fat from your fingers will remain on the glass and will begin to evaporate during operation at high temperatures - its deposition on the optics will lead to clouding and poor visibility.

The change in dimensions looks like this:

We unscrew the screws securing the fender liner and remove it;
We unscrew the socket with the light bulb, turning it counterclockwise on the right, and clockwise on the left;
We unscrew the burnt out product and screw in a new one;
Then we proceed in reverse order.

We proceed in the same way with turning lights:

Unscrew the screws and remove the fender liner;
We turn out the cartridge;
We change the light bulb and screw the socket back;
We return the fender liner to its place.

The situation with fog lights is similar:

Remove the fender liner;
We snap off the holder and disconnect the block;
Turn the lamp 1/3 turn counterclockwise and remove it;
Installing a new one;
Then we proceed in the reverse order.

Some drivers manage to gain access to the headlights through the engine compartment without removing the fender liners and battery - this requires dexterity and some experience.

Replacing the headlight

Now let's see how to remove the headlight on a Lada Largus if you need to replace or repair it:

First, remove the wheel from the side where you are going to change the light.
Unscrew the fastening screws and remove the fender liner.
Disconnect the wires.
Remove the block.
While turning, remove the marker and turn signal cartridges.
Open the hood, remove the lamp cover and remove the block.
Disconnect and remove the hydraulic correction cable.

Remove the front bumper to gain access to the light mounts.
Unscrew the three bolts - use a ten-point socket to do this.
Remove the headlight and install a new one in its place.
Reassemble in reverse order.

Changing lamps and headlights on the Lada Largus is one of those types of work that will not cause difficulties even for a beginner. Of course, if you do not have experience, you will have to spend a little longer, but if you carefully follow the instructions, the result will be successful.

From time to time, replacing a Lada Largus lamp becomes one of the mandatory procedures. The reason for this is that it becomes unusable, which in the dark is not only uncomfortable, but also life-threatening.

Lighting elements of Lada Largus

halogen;
xenon;
LED

Replacing the low beam lamp, as well as the high beam, begins by disconnecting the on-board power supply.
This precedes all electrical repair work. In this case, a special switch is turned or the negative terminal is disconnected from the battery, which avoids accidental short circuits or erroneous connections during installation.
The place where the Largus lamp will be replaced is determined.
There, the rubber plugs covering the electrical components are removed, and two metal antennae are opened in front of the car owner, fixing them in the reflector. They are separated so that the used parts can come out of their seat without damaging the housing.
Next, you need to disconnect the plugs from the wiring that was previously disconnected. Here it is worth paying attention to the order of arrangement, otherwise, during the installation of new parts, everything can be mixed up and they will have to be changed again.
After connecting the plug with wiring to the new parts, they are mounted in place and secured with antennae. You should try not to touch the flasks with your hands, as this can lead to their rapid failure.
If the light is dim during lighting, and the headlights flash when you turn on the headlights, then it is imperative to restore the contacts of the wires with the vehicle body. This is especially true for a marker lamp, because the fat that gets there begins to evaporate when heated and can cause ignition.
At the end of this procedure, you need to put on the rubber plugs and secure all the parts in their places. After this, the car will be ready for use and the driver does not have to worry about malfunctions of the Lada Largus lighting fixtures.

The principle of replacement is similar to the installation of the above-mentioned lamps, but it has its own nuances. Here, first, the trunk lid is opened and its decorative panel is removed. So, in order to replace the brake light, you must first of all clear the approach to the wing nuts.

After removing them, the entire headlight is turned out, which would be very problematic to do on your own. After all, you need to bring out its upper and lower parts at the same time so that they do not become a surprise. After unscrewing the screws, access to the lamp is open. The failed part is replaced, and all the previously listed steps are performed in the reverse order.

After opening the hood, disconnect each wire from the turn signal. To do this, you need to release the spring tip by pressing its lock. After a characteristic click, pull out the part.

Dimensions

To replace the side light bulb in Largus, the socket of the old part is turned counterclockwise. The black and yellow wires connect it to the battery, so it turns off from them. A new part is installed in this place, and assembly is carried out in the reverse order.

You need to make it a rule to regularly change not only the lamps, but also monitor other lighting elements. After all, the process of reducing their brightness occurs slowly and the driver simply does not notice the deterioration in road lighting.

Source: https://avtozam.ru/vaz/zamena-lampy-blizhnego-sveta-lada-largus-vaz-lar.html