How to start a car with autostart kgb. Installation of kgb alarm

The instructions for the KGB anti-theft system consist of several pages. Only after carefully studying it can you fully use all the alarm functions. One of the important sections is programming the transmitters (you can record up to four remote controls). But if, after reading the instructions, you still doubt your actions, then let’s figure out together how to set up the KGB alarm key fob.

Programming the new KGB remote control with feedback

Replacing a broken communicator KGB GX 3, FX 3, G 2, EX 7 implies recording it in the memory of the control unit. For this.

Turn the ignition key to the “On” position.
Press the Jack key and hold it for six seconds. After four beeps sound, release the service button.
Press keys 1 and 2 at the same time. The siren will emit one squeak.
Enter the codes of the remaining transmitters in the same way. Programming each remote control is accompanied by a corresponding number of sounds.
If you do not press the buttons on the key fob within six seconds, the control unit will exit the setup mode. The lights will flash five times.
Deactivate the ignition.

Remember that when recording new pagers, do not forget to re-register the old ones in order to avoid their deletion from the system memory.

How to enable autorun

To set a car alarm to autostart, you must follow the installation and configuration rules of the system. Warming up on the Tomahawk can only be activated if several rules and conditions are met.

If your vehicle is equipped with an automatic transmission, it will not be able to remotely start the engine without moving the lever to park. If a manual is installed, the lever must be placed in the neutral position on the handbrake, after which the corresponding indicator on the dashboard will light up.

Next, you need to remove the keys from the ignition, get out of the car and activate the security functions with the button on the key fob.

If the engine is deactivated, then autostart is enabled.

To prevent unforeseen circumstances, you should adhere to the following user manual:

On the communicator, you need to activate the right open button and hold it until a 2-second signal appears. Then the button must be released.
If activated successfully, the key fob will give an audible warning and the car will flash its headlights several times. A similar phenomenon will confirm the activation of the automatic start function.
The key must be turned in the ignition and removed.
Next, you should leave the salon, close the door and turn on the security mode.
After the appropriate command from the key fob, the engine will be started.

How to set autostart by temperature

A useful feature of Tomahawk alarms is the ability to auto-start based on temperature. It is provided by a special sensor installed under the hood, which is triggered at a temperature range below +5 or above +30°C.

If there is no sensor, you will need to install autostart based on temperature using a sensor inside the cabin. To activate automatic engine start, you will need to perform the following manipulations:

Press the trunk open button and the “key”.
Wait for the light indication and sound signal to appear.
The “Snowflakes” icon and the set temperatures will appear on the monitor.
A beep will sound.

Then the system will function automatically, guided by the specified interval. To deactivate the function, you will need:

Press the “Trunk Open” and “Key” buttons.
Wait until the parking lights turn on and off twice.
Wait until the “Snowflake” disappears from the screen.
Wait for the melody that will signal the successful completion of the operation.

How to change autostart temperature

To change the autostart temperature and set a different value, you will need to study the operating instructions and select the desired setting.

How to set it to autorun by time

To start an alarm with an automatic winding function at a selected period of time, you can set these parameters in the settings menu. To do this you need to perform the following manipulations:

Simultaneously press the combination of the “Key” and “Mute” buttons.
Wait until the parking lights turn on and off once.
Wait until the “Clock” icon on the key fob lights up.
Wait for the sound notification.

If the driver has set this setting, the next day the car will turn on automatically at the command of the time indicator. To disable the function, everything is done in the opposite way:

Simultaneously press the “Key” and the mute key.
Wait until the headlights light up twice.
Wait until the “Clock” icon disappears and the sound signal disappears.

How to set up automatic restart at certain intervals

To set up a car factory at an interval, you need to do the following:

Activate the "Key" button.
Wait until the headlights come on and off.
Wait until the beep sounds indicating the completion of work.

One of three icons will light up on the display: “St”, indicating an attempt to start, “SP” - an unsuccessful attempt, “Car” - the system is working without failures. In the latter case, a beep will sound.

The function operates at a specified time interval, after which it turns off and turns on again.

How to extend the warm-up time

To set the time range to 1, 2, 4 or 12 hours (in some models you can set more time), you need to hold down “Key” and “Mute”, and also hold the start key for 5 seconds. Depending on the selected interval, you must perform the following actions:

1 hour - “Castle”.
2 hours - “The Key”.
4 hours - “Open trunk”.
12 o'clock - "Sound off".

The interval varies depending on the surrounding conditions. If the timer is set in winter, you need to turn off the stove to prevent it from accidentally warming up the interior. In this case, the car will warm up faster.

Depending on the signaling model, the function can be configured according to other principles:

Until the signal appears, you need to hold the right “Open” button.
When the alert sounds, release the button and press Close.
The “2-1 daily” icon at the bottom will light up, indicating that the timer function is enabled.

If you follow the instructions, the car will start and operate for 5 minutes at intervals of 1 hour.

How to extend the warm-up time

If you need to change the factory settings and extend the warm-up time, use the Override button, which is pressed as many times as necessary to enable a function. Using the communicator, you should adjust the time indicators.

To turn off the function, you need to perform the same steps by clicking on the “Open” button and then “Close”. When the “2-1 daily” sign disappears, you can be sure that the timer has turned off.

Setting up autorun from the KGB key fob

You can start the engine from the alarm switch KGB FX 5, G 5, FX 10, GX 5 RS, F X 8, FX 7 (fix 7) in two ways.

Move the cursor to the “START” symbol and press button 2.
Press key 1 for three seconds. The engine will start. The side lights will flash three times and a melody will play on the key fob. The LED will light up continuously.
The screen will display the “Smoke from the exhaust pipe” symbol and the set engine warm-up time (5, 10, 15, 20 minutes).
One minute before the end of warm-up, r01 will appear on the display, a sound signal will follow, and the side lights will light up four times.
After stopping the engine, the message r00 will appear on the screen, and the “Smoke from the exhaust pipe” symbol will disappear.

To program autostart of the engine based on temperature, do this.

Move the cursor to the “START with thermometer” icon and press button 2.
The siren will sound once, the side lights will work once, and a melody will play on the remote control.
The “Thermometer” symbol will be displayed on the screen, indicating that autostart is activated based on degrees outside and the temperature value (-5, -10, -20 -30). The LED will flash.
To turn off automatic start based on temperature, move the cursor to “START with thermometer” and hold down button 2. The siren will sound twice, the dimensions will blink twice. A melody will play on the pager. The Thermometer symbol will disappear.

How to set up autostart on KGB alarms: by temperature and time

Auto start is a convenient function of the alarm system that allows you to start the car remotely, from the key fob, or at a given time according to a schedule or when the temperature outside the window reaches a certain value.

Remote engine starting is implemented in many KGB alarm models, namely:

GX-5RS;
G-5;
FX-10;
FX-8;
FX-7;
FX-5.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

All of the mentioned models allow you to remotely start the engine with a command from one of two key fobs, remotely turn off the car, and also set the autostart time according to a schedule or select the temperature at which the car will start itself.

The control elements - key fobs - of all alarms in this list are structurally similar to each other. One of them is equipped with a feedback function with the machine and a liquid crystal display, the second serves only to issue commands. Despite this, the buttons on both key fobs in all of the listed alarms are duplicated and perform the same functions.

There are 3 of them in total. Button 1 is equipped with a pattern in the form of a closed padlock, button 2 has an open padlock, button 3 is designated Prog in different models. or AUX.

The exception is the FX-8 model, where button 1 is marked as an open-close lock, button 2 has a pictogram in the form of a profile of a car with an open hood.

On the FX-5, the buttons are labeled I, II and (*).

KGB autostart in different models starts in an almost identical way, only some alarms have an alternative mode.

Please note: the warm-up time for diesel engine spark plugs in all models is programmed by the owner at his own discretion. It can be set to 4, 6 or 10 seconds. If the warm-up mode is turned on for a gasoline engine, the time is always standard - 4 seconds.

How to start the car?

Starting a car from the key fob varies slightly across different models. For example, the FX-5 alarm has two options for this: from the main and from the additional key fob (on the main one you can use any of them of your choice).

Method 1: on the main key fob you need to select the “Start” icon and press key II.
Method 2: press the I key on any key fob for at least 3 seconds.

Attempts to start are accompanied by light and sound signals.

On the FX-7, remote start is carried out by the following command: holding button 1 until the sound signal sounds, and confirming the operation by pressing button 3. Successful start is also confirmed by light and sound signals from the car and from the key fob.

To remotely start your car with the FX-8, you need to take the same steps as with the FX-5. Only the icons on the buttons differ.

The FX-10's remote start is exactly the same as the FX-7's. The engine starts in the same way on the G-5 model. But the GX-5RS modification has differences: first you need to press the button with the lock closed (the first button) and hold it until a beep sounds, and then confirm the operation by pressing the same key once.

Please note: the remote start only works for a short time - 10, 20, 30 minutes - or without a time limit. The engine operating time in this mode is programmed individually.

By temperature and time

You can set a car with any of the described alarms to autostart based on temperature or time. Temperature-based autostart on the FX-5 occurs when the ambient air temperature drops to -5, -10, -20 or -30 degrees Celsius. The specific value is programmed by the owner.

Installation is carried out only from the main key fob. You must select the Start icon with a thermometer on the display and press button II. The thermometer icon will appear and the temperature value at which the motor will automatically start.

Similarly, only using the Start icon with a checkmark, a timed start is carried out. The system remembers what time the first launch occurred, and all subsequent ones will be carried out at the same time.

The actions on the FX-8 are completely similar.

On FX-7, F-10, G-5, GX-5RS, to set autostart based on temperature, you need to press and hold button 3 until the key fob emits 1 long and 1 short signal.

After this, you need to sequentially select the Temp icon. Start. Confirm your selection with 1 key.

The base temperature at which the engine will turn on automatically is -10 degrees; it can be changed by sequentially enumerating the values.

Setting autorun by time is carried out in exactly the same way, only the icon with a “checkmark” is selected. You can disable autorun using the same principle, only button 2 is used for confirmation - “open lock”.

The starter cranking time in each model is set by the owner of the car in the range of values from 0.8 to 3.6 seconds. Time can be determined by the operation of the generator or tachometer.

Shutdown

It is also possible to turn off the engine using a command from the key fob. To do this, in the FX-5 and FX-8 modifications, you must press and hold button 1 until a four-time light and sound signal is heard - the engine is turned off, the security mode is on. To stop the engine and disarm the security, after holding 1 button for a long time, press it once.

To turn off the engine in a car equipped with FX-7, FX-10 and G-5 alarms, you must press and hold the second button until the sound signal sounds, and confirm the command by pressing key 3. On the GX-5RS, a similar order to the car is given by pressing and holding + repeat by pressing 2 keys - “unlock”.

Reasons for refusal

If the remote or start does not work, then one of the possible reasons could be:

open hood;
ignition on;
pressed brake pedal (for cars with automatic transmission);
handbrake is off.

In addition, the warm-up time for the spark plugs may not be programmed or selected incorrectly (relevant for diesel engines) or the type of gearbox may not be set - for a car with a “mechanics” it is necessary to cut the black wire loop in the wiring harness of the central unit. Eliminate these shortcomings and the system will work.

Tired of paying fines? There is an exit! Forget about fines from cameras! An absolutely legal new product - Traffic Police Camera Jammer, hides your license plates from the cameras that are installed in all cities. More details at the link.

Absolutely legal (Article 12.2);
Hides from photo and video recording;
Suitable for all cars;
Works through the cigarette lighter connector;
Does not cause interference to radios and cell phones.

Find out details

Source: https://AlarmSpec.ru/signalizacii/kgb/nastrojka-avtozapuska-kgb.html

Instructions for registering old remote controls

Activation of the anti-theft system switches KGB VS 5000, MX-9, ex 8 series, VS 4000, tfx 5 (tfx 5), ex 7, VS 130, AX-5 begins with entering the programming mode.

Activate the ignition.
Triple-click the Valet button to pair the remote with a one-button configuration.
Click on the “Valet” key six times to record a two-key fob.
The siren will sound once. You have entered setup mode.

Follow the instructions below to record pagers.

Press any key on the first remote control. One signal will play.
Press any button on the second remote device. The siren will sound twice.
Following the previous steps, register the remaining transmitters.
Exit setup mode by turning off the ignition or without pressing anything for fifteen seconds. The system will confirm exit with three siren signals.

Emergency activation and deactivation of the alarm system

If the car does not respond to the key fob, you can use the emergency activation and alarm disabling function.

Emergency alarm activation

To activate an emergency alarm, you must:

turn on the ignition, but do not start the engine;
press the Override button eight times;
turn off the ignition.

The car will react with a single flash of the parking lights and a single sound of the siren. After 20 seconds, the system will automatically turn on the security mode.

If, 20 seconds after the emergency activation of the alarm, any of the security zones are triggered, the car will notify the user of this by flashing the parking lights four times and sounding the siren four times. After this, the user will have 20 seconds to disarm it. If this is not done, the system will activate the alarm mode.

Emergency alarm shutdown

To make an emergency shutdown of the alarm without a key fob, you must:

turn on the ignition (do not start the engine);
press the Override button four times;
turn off the ignition.

The parking lights will flash twice and the siren will sound twice.

REFERENCE. The key fob pager will continue to function even after the user has made an emergency activation or emergency shutdown of the alarm system

Responsible drivers independently determine how to provide their car with protection against theft, as well as eliminate problems with starting the engine during cold periods. Some of them install a Tomahawk alarm system with auto start on their car. It allows you to start and warm up the engine without leaving the building. But in order to avoid problems with the operation of a car alarm with an auto-warming function, it is important to fully understand how to use it.

Why doesn't it get attached?

Flashing key fobs for the KGB security system VS 100, 5500, 200, 5900, 300, 5700, 400, 250, 500, BC 150, tfx 7 is not always successful the first time. Why can’t you reprogram the remote control and how to get out of this situation.

Service mode was accidentally activated. Turn it off by pressing the “Valet” button and repeat the firmware procedure.
The “Ignition activated” command is not detected by the alarm control unit. Contact a service station.
Switch failure. Repair it yourself or take it to a specialist.
Failure of the control unit. Take the car to a service center.

The car will not start with the Tomahawk alarm key fob

Some users complain that the remote control screen shows an SP error and starting from the key fob has stopped working. There may be several reasons for this phenomenon. Below is a detailed description of problems such as why the Tomahawk does not start the car in cold weather and the pager beeps.

Pre-launch preparation was carried out incorrectly. It is necessary to check the location of all elements and controls. Car enthusiasts often forget to put the car in neutral.
Severe battery drain. Users are especially confused by the situation when the car starts normally with the key. This is due to the fact that when executing a command remotely, the machine needs more voltage than during the standard procedure. Charging the battery or replacing it with a more capacious one can help correct the situation.
A similar problem - the internal combustion engine does not start, but the indicator says the opposite. The malfunction is explained by setting the on-board voltage and operates as follows: the starter turns over - the voltage drops, the engine does not turn on. The chain has aligned - the system perceives this as successful completion of the task. It can be cured by changing the tachometer speed setting.
Malfunction of the door limit switches, trunk lid or hood. Sometimes the sensor contacts can move away or become heavily oxidized - this disrupts the signal flow, which is read by the on-board computer as the “open” position, even if physically all the panels are securely locked. It is also recommended to check the drives themselves for oxidation and mechanical damage.
System error. Rarely, but it happens, it's Tomahawk. A complete reboot of the alarm helps here. To do this, you need to disconnect the battery terminals for 15 minutes and connect everything back. In extreme cases, the head module is sent for repair.
Lost connection with the key fob. The battery in the remote control may also be dead. This is also possible if there is a large amount of electronics around the car, a pager. You can replace the battery or come closer to the car and repeat the procedure.
Severe freezing. If the vehicle has been standing for a long time in severe frost, the oil in the crankcase thickens and prevents the crankshaft from turning, which seriously complicates starting. If this happens often, it makes sense to set up autostart based on engine temperature or timer. This can be done in the programming menu.
Starter operating time is too short. In the settings you need to set the pulse interval. If this happens in winter, it is recommended to extend the scrolling to the maximum value.
The antenna is damaged - the module is sent for diagnostics or completely replaced.
In some cases, “witchcraft” with device binding helps. For example, the start is connected to the tachometer, but does not work correctly. It is recommended to reconnect the alarm to the oil pressure lamp or DPKV.

From the above it is clear that the Tomahawk system is quite capricious in terms of setting options. But if everything is done correctly, there will be no problems in operation.

How to set the time on a KGB key fob

Setting the clock on the KGB anti-theft system remote control begins by entering the installation mode by pressing and holding the “SET” button.

After one second, a short signal from the transmitter will follow. The screen backlight will turn on for five seconds.
Continue holding the SET key.
After two seconds, two beeps from the key fob will sound. You have entered the current time setting mode.
Release the SET button.
Set the clock. The “Trunk Opening” button increases the values, the “Speaker” button decreases.
To go to setting the minutes, briefly press “SET”.
Set the number of minutes. The “Trunk” key raises the numbers, the “Siren” key lowers them.
To exit, press “SET” for two seconds.

A security system today not only protects the car from theft, but also increases user comfort with additional functions: power window closers, auto start, geolocation.

A reliable and uncomplicated “alarm” KGB TFX-5 can be a good choice; in its instructions you can find complete information about system installation, configuration and further operation.

Characteristics

Functional properties of the KGB security system for a car:

the ability to remotely turn on, turn off and configure the option of remote start of the car engine by time or interval;
optimal operation of the security system with both diesel internal combustion engines and gasoline engines;
the latest models of KGB signaling systems have implemented a more convenient interface for monitoring the start procedure and engine operation;
engine start by timer or in accordance with air temperature;
independent controllers are used to control the temperature in the car interior;
when the protection mode is deactivated, the power unit is unlocked in two steps;
independent indication of activation of security system controllers by level;
the consumer will be able to additionally install regulators to control the machine’s security;
when using KGB car alarms, the consumer has the opportunity to implement several different options for emergency disabling the anti-theft complex, in particular, using a password;
engine operation can be monitored by indicating an engine fluid pressure sensor, a tachometer, or the voltage level in the electrical network;
auxiliary channels can be used for control and configuration, there are four in total.

Features typical for a pager with a color screen:

The body of the device is equipped with a rubberized main body. This prevents the pager from slipping in the car owner's hands and ensures the remote control's resistance to mechanical stress.
Depending on the model, the device can control at least six security zones. Indication on the pager display is in the form of pictograms.
The complex's pager has an energy saving option. It's called Power Save and is only present in devices with two-way communication. Activating the option allows you to increase the battery life.
The pager has fluorescent backlight. This makes it possible to control the KGB alarm and read data from the pager screen at night.

Specifications

Temperature conditions of normal operation: for the pager - 0... +400°C, siren - -30... 850°C, the system itself - -40... +850°C.

The alarm works with no more than 4 transceivers.
Using the system, you can organize 6 security zones.
Operating currents in active mode are minimal - up to 25 mA.
Supply voltage - 12 V, from the on-board network.
1200 m - radius of operation of the receiver in open areas.
600 m - two-way communication range between the key fob and the car.
The KGB TFX 5 alarm system with auto-start operates at a frequency of 433.5 MHz.

Two-way car alarms

Among the wide range of KGB car alarms with two-way communication, it is worth noting the models AX-5, EX-6, FX-3 improved version, MX-9. All such devices are full-fledged security systems, which are controlled by a key fob with a liquid crystal screen and a warning range from 1200 to 1800 m. Models FX-3.10, MX-9, EX-7 are a system with.

Along with standard functions, each of the presented modules is equipped with a set of additional protective capabilities. Anti-HiJack deserves special attention - powerful and reliable protection against scanning and hacking.

KGB TFX 5

The video shows the installation of a KGB car alarm with auto start:

One of the best representatives of this class is the KGB TFX 5 car alarm with automatic engine start. The system differs from similar devices by the presence of a unique signal encoding algorithm. The product is optimal in terms of price-quality ratio, the KGB TFX 5 system works. Starting the engine itself is possible:

by time;
at the command of the key fob;
by temperature sensor.

The KGB TFX 5 car alarm instructions, which come with each kit, will help you install the system yourself.

Equipment

The element base of the complex includes:

central block;
key fobs transmitters: with LCD display and feedback with 3 buttons and additional with 4;
to measure the temperature in the cabin, a special sensor is used, built into the antenna unit along with the driver call button;
two-level shock sensor;
LED indicator;
siren;
Valet - service button for KGB car alarm;
“Anti-robbery” key;
limit switches;
set of wires with connectors;
batteries, stickers;
instructions, memo, warranty card.

Security system capabilities

The first thing that catches your eye when you get acquainted with the electronic watchman is the abundance of simple and useful functions. The developers used a method popular in the industry: they divided the car into 9 zones and installed their own protection method for each. Starline alarm system includes:

a relay that prevents unauthorized engine starting;
sensors (micro switches) for the trunk, hood and doors;
two-level shock sensors to protect glass and body elements;
parking brake lock;
control of the ignition switch position.

Starline A93 review:

The operating instructions contain details about options that improve usability, increase security and prevent the possibility of hacking and control interception:

dynamic coding of the control signal;
turning on sound and light notifications (alarms) for a limited period of time;
disabling alarms without disarming the vehicle;
saving settings even when the power is turned off;
simulation of engine malfunction (anti-robbery mode);
the presence of an individual access code, which makes it possible to urgently turn off the alarm.

Alarm "Starline" with auto start , according to the instructions, has several ways to notify the owner and others about an attempt to steal or enter:

turning on the siren and lights;
alarm notification via key fob with feedback;
“panic mode”, in which light and melodic alerts are forcibly turned on.

A feature inherent in the Starline series of alarm systems with autostart function is the ability to self-diagnosis. The control unit constantly scans the status of the sensors. If a malfunction is detected, it signals this to the owner using an LED indicator and a notification system via the key fob.

How the system works

All work of this system is carried out using a special, secure protocol and comes down to the simplest principles of a conventional encoder. A special algorithm with a secret code allows the key fob to process the incoming signal and send a response back to the sensor. In this case, the system turns off only when the sent and received signals match, and a confirmation is received on the key fob. All this takes just seconds!

Functions

The security complex performs the following protection functions:

A notification appears on the LCD display of the key fob when the system is activated.
In security mode, when the sensors are triggered, alarms are activated in the form of sound and light.
The “Panic” and “Anti-robbery” modes are activated remotely, and the latter can also be activated by a button.
There is an immobilizer capability.
The engine blocking is maintained even if the alarm is removed.

The service capabilities of the KGB FX-5 alarm system include:

security without noise and with the engine running;
turning on protection without key fob and sound;
ability to arm passively and repeatedly;
different door unlocking options;
the presence of an alarm clock, timer, thermometer;
search mode.

In addition, using the system, the car owner has the opportunity to start and warm up the engine from a distance, program the FX-5 so that it starts at the right time or at a programmed air temperature, taking into account the characteristics of the engine type (gasoline or diesel) and the type of transmission.

Advantages and disadvantages

According to reviews from installers and users, the FX-5 has the following advantages:

Low cost with a good price-quality ratio.
The installation and configuration process is clearly described in the manual.
Advanced functionality.
Powerful siren included in the kit.
Confident and reliable operation of remote engine start.

Disadvantages inherent in the complex:

A large number of false positives due to installation and configuration errors.
A defect in the key fob occurs relatively often and forces the user to press the buttons again.
If the shock sensor is not configured correctly, its sensitivity allows an attacker to remove, for example, the windshield wipers.

Causes of problems

The most common reason why there may be problems with car silencing may be related to the condition of the batteries. In addition, the electronics in the key fob may be damaged. You cannot use remote controls that are not specified in the system settings. In this case, you can turn off the engine using an additional remote control or by opening the car with the key and entering a password on the control unit.

If the car starts successfully, but after a couple of minutes it turns off and the engine does not start, check how the temperature sensor works. It is located in the engine compartment. In addition, the security system itself may be installed incorrectly, resulting in a problem with autostart.

If the car owner uses a mobile application, the cash balance of the SIM card installed in the alarm system should be monitored. If there is not enough money, SMS commands and the Internet connection will not work.

Installation instructions

The delivery set includes instructions for installing the FH-5. Before installing the equipment, you must disconnect the car battery.

System installation procedure:

Determine the location of the central block. Fasten it to the car using self-tapping screws.
Place the siren under the hood in a place that does not heat up, pointing it down with its horn.
It is better to place the Valet button in a point in the cabin that is hidden from an attacker, but accessible to the owner of the car.
Install the “Anti-robbery” button.
The transceiver is placed on the windshield using tape or a sticker. Attach the antenna and LED indicator.
A coolant temperature sensor is installed into the cooling system.
“Limit switches” are placed on the hood, trunk and doors in the connectors available in the car.
A shock sensor is located in the central part of the body. They are fastened with self-tapping screws and then adjusted.

In KGB FX-5, the instructions for the alarm contain the necessary diagrams for connecting the elements:

main block;
6- and 18-pin connectors;
electric lock drives.

How the function works

Before purchasing a Tomahawk alarm with auto start, you need to understand how auto start works and what it is needed for. The operating principle of the system is quite simple: the driver sets operating parameters using an electronic board, to which sensors and ignition contacts are connected via a relay. The control unit is installed in a comfortable and freely accessible place, and then connected to the rest of the devices on the panel.

The device is controlled from a smartphone running iOS and Android or from a key fob. When the system checks the pressure, the starter engages after 2-3 seconds. In the case of diesel engines, a preliminary check of the storage plugs is carried out.

To warm up the Tomahawk and configure autostart, you can select one of two operating modes:

Manual control using key fob.
Autostart via a command from a mobile application.

The Tomahawk auto-start alarm system has the following parameters for configuration:

Motor operating time. This indicator varies from 5 to 20 minutes. In standard mode it is 10 minutes, but in winter it is better to increase it.
Temperature indicators at which the engine autostarts. They are measured by a unit installed in the cabin, and not by a sensor near the engine. In this case, the car owner independently adjusts the temperature in the range -5...+30°C. In normal mode - -10°C.
Cranking time of the crankshaft by the starter mechanism. The values vary and range from 0.8 to 3 seconds. The basic setting for the Tomahawk 90 timer model is set to 0.8 seconds. When the engine control option via tachometer readings is activated, the system automatically turns off the unit, so it is better to select an interval of 3 seconds. If the function malfunctions, each time you try to start, the parameter changes by 0.2 seconds.
Method of controlling the power unit. Modern Tomahawk alarms, which are controlled from a remote control, have the following control options - by voltage of the electrical network, by tachometer readings or by an indicator of fluid pressure in the engine.
Duration of operation of the second channel. This function must be changed when installing an immobilizer bypass. The valid range varies from 0.8 to 30 seconds. It is also possible to operate the channel during the entire autostart time.
Starting delay between activation of the ignition circuit and the starter mechanism. For engines operating on gasoline fuel, the indicator is 2 seconds, and for diesel units - 2-10.

User manual

The instructions for using the security system contain recommendations for programming and configuration:

key fob buttons and codes;
protection and energy saving modes;
turbo timer and anti-robbery.

The manual suggests programming the system using the Valet button. To enter the mode you need:

With the ignition on, press the service button 6 times, then turn off the ignition.
The correct action will be confirmed by 6 beeps and the LED indicator will blink 6 times.
Select the function needed for programming from the table.
Use the key fob to set the required value.

The power saving mode is set and removed as follows:

Press and hold up to two melodic signals the button with the sun-shaped icon on the key fob.
Move the indicator to the icon with the inscription Save and the image of the battery.
The first button is to activate the saving mode (the second is to deactivate).
Holding the sun icon until the sound signal exits programming.

You can enable protection while the engine is running as follows:

With the engine running, turn on the handbrake.
Press and hold 1 pager button until the remote control makes a melodic sound and the lights blink 3 times. In this case, the indicator diode will light continuously, and the display will show the operating machine.
When the ignition is turned off and the key is removed, the engine should be running.
In 30 seconds you need to get out of the car, close the doors and press button 1 on the key fob.

Badges and buttons on the key fob

The operating instructions contain a detailed description of the purpose of the indicators on the LCD display and the key fob buttons.

The main key fob has the following indicators:

opening or closing door, hood and trunk locks;
turning off the handbrake;
body impact;
security with and without sound;
Valet mode;
the motor is running;
operation of 2 additional channels;
autostart based on air temperature;
battery status;
availability of communication;
turning on the ignition;
1 or 2 half day;
daily start by time;
temperature and time;
timer, etc.

Purpose of key fob buttons:

1 button - stop and start the engine remotely when held for more than 3 seconds or execute a programmed command;
2 - the button, when pressed for 3 seconds, opens the trunk door, and also implements a function corresponding to the position of the cursor on the LCD display when pressed briefly;
the search is activated by simultaneously briefly pressing keys 1, 2, and if you hold both buttons for 3 seconds, the “Panic” mode will turn on;
the notification selection will open when you press buttons 1 and 3 at once;
The timer can be set by pressing 2 and 3;
Button 3, with a short click, moves the cursor through the icons; with a three-second hold, you can view and set the alarm, timer, clock, energy saving, and after waiting 6 seconds, it becomes possible to set a command to button No. 1.

How to enable autorun

To set up and start the internal combustion engine remotely or use the automatic start function in TFKh-5 based on temperature, you need to:

In a car with a manual transmission, engage neutral gear and park with automatic transmission.
Put the car in handbrake.
Place the car in a ventilated place.

After this, if you move cursor 3 with the key fob button to the Start icon and confirm by pressing button 2, the dimensions will blink, the siren will sound and the key fob melody will sound. All this means that the daily autorun mode is now enabled.

Setting up the system from scratch

Having opened the instructions for the KGB signaling, you can immediately find the table:

Customizable Features

The settings responsible for autostart alternate with security options, but there is nothing wrong with that. You can download the photo and print it on a printer - no changes were made during copying. Don't forget to connect the Valet module as well as "cord 5" of the power connector. You will also need the KGB TFX key fob.

Programming order

To access the settings, follow a set of steps:

Turn on the ignition, press the Valet button 6 times, then turn off the ignition;
There should be 6 beeps and 6 LED flashes;
By pressing the Valet button, select the option number;
By pressing a key on the key fob, a new value is set;
Steps "3" and "4" can be repeated;
Finally, the ignition is turned on.

You can also perform a “reset”. The amendments will be as follows: in step 1 you need not 6, but 10 clicks, and in step 3 select “option 1”. Then press “key 1” on the key fob, as when selecting “value 1”. The settings are reset to “factory values”.

System control panels

The TFX 5 key fob has a AA battery. Carry out all replacement actions near the alarm itself. Having removed the “old” element, press key 1 briefly. Then a “new” battery is installed.

Idle training

If the control cord was connected to the tachometer, function 8 is assigned a value of 3 or 4. But this will not be enough. Training required:

First, turn on the ignition, press the Valet button 9 times and turn off the ignition;
There should be 9 beeps;
The ignition is turned on, the engine is started, and wait until constant speed is established;
Press and hold the Valet button until a beep sounds or the LED goes out.

As a result, the alarm will recognize engine speed.

It is better to control the engine using the tachometer signal. You can install two parts into the wire gap: a capacitor with a capacity of 1 mKF (47 Volts) and a resistor of 400-600 kOhm.

Capacitors MBM 0.5 mKF

User manual

The product has been produced by a Russian company since 2001. During this time, the company has occupied a large market share, and the system is sold not only in Russia, but also abroad. This happened thanks to reasonable pricing policy and constant innovation.

One of the most popular signaling devices is the KGB TFX 5, but there is another variety of this model - KGB FX 5. The instructions for them are almost the same, the only difference is the presence of a transponder in the delivery kit, indicated by the letter “T” in the name.

Additionally, we recommend reading the article by our expert, in which he talks in detail about the advantages and disadvantages of the Sheriff car alarm.

We also recommend reading our specialist’s article on the pros and cons of the Alligator alarm system.

You may also be interested in our author’s article, which provides detailed operating instructions for the Starline A9 alarm system.

The main characteristics of the alarm are as follows:

system operating distance is 600 m, and in open areas - up to 1,200 m;
the control module and the key fob exchange commands at a frequency of 433 MHz;
power is supplied from the car battery;
number of security zones - 6 pcs;
when fully activated, consumes 25 mA;
supports connection of up to 4 transmitters;
the system can operate in the following temperature conditions: -39 to +84 °C.

The advantages of KGB TFX 5 include:

the instructions are very detailed and describe all aspects of interaction with the alarm;
the price of the system does not exceed 6,000 rubles, which is a very good offer in this category;
quite rich functionality for this price;
high volume of the siren, which can scare off intruders;
Automatic engine start works stably within the range from -39 to +84 °C.

Among the disadvantages are the following:

if the alarm is installed incorrectly, the shock sensor does not work; this also happens with the minimum sensitivity set;
In some sets the key fob does not work correctly and does not always work. This problem can only be resolved by exchanging for a new device;
a large number of false alarms are caused by incorrect sensitivity settings, at the maximum values of which the alarm will be activated by a passing car.

Contents of delivery

The system is supplied as follows:

key fob, which is equipped with 3 buttons and a display;
control module;
a transceiver that is equipped with a temperature sensor;
indicator light, it shows the status of the alarm;
siren;
shock sensor with wire for connection;
button to activate the “Anti-Robbery” mode;
kit and wires for connecting a remote engine start unit;
separate button to start service mode;
cables for mounting the control module;
connectors for connecting to electric door locks;
user manual, which can also be downloaded from the manufacturer’s website.

Alarm installation

Before installing the KGB TFX 5 alarm system, be sure to read the instructions. The system is installed in the following order:

de-energize the car by removing the terminals from the battery;
selection of installation location. It is advisable to avoid the area under the driver's seat and behind the center console, as this is where intruders will look first. The best area to use is behind the dashboard. To avoid exposure to vibration, you need to wrap the block with foam rubber and secure it with self-tapping screws;
The siren is mounted under the hood of the car, away from the engine. High temperatures can cause equipment failure. The horn should be pointed down or forward, but not towards the driver;
The Valet service mode key is installed in a hidden place, but to which the driver has access. If installed incorrectly, a criminal will easily gain access to it and be able to disable the entire system;
The antenna adapter is installed as high as possible, as this increases the stability and operating range of the system. The best place for this is the windshield. The block is held in place using double-sided tape;
The temperature sensor, which is necessary to enable auto-start of the engine, is installed in one of the cooling pipes. It must be securely fixed so that it is not torn off by the refrigerant. The power cord is led out;
special switches are installed on the trunk, hood, and doors. To do this, technological connectors must be present in the body;
The shock sensor is mounted inside the car. After installing it, you need to configure the device. The best place for installation will be the central part of the partition, which separates the interior from the engine. Fixation is carried out using self-tapping screws;
After connecting all the elements, the battery is connected.

Two way security system

There are several models that meet the technical characteristics of this security system (kgb fx 3, 10, 8, 5, kgb tfx5, ex 7, 6, 3). Despite this variety, all of these anti-theft systems with auto start have similar functions:

the key fob is equipped with a bright liquid crystal screen;
the signal sent from the car to the key fob operates at a distance of 1.8 kilometers;
presence of auto engine start;
special technology that protects the signal from being read.

The KGBtfx 5 alarm system with auto-start deserves special attention; the instructions for this security system provide for several new options for automatic start of the power unit.

Alarm system with auto start KGB tfx 5, in addition to general technical characteristics, has several functions of automatic engine start:

starting the engine in timer mode, that is, the car owner independently sets the time when the car’s power unit should start (this function is designed for gasoline and diesel engines);
starting the engine using the command, that is, by pressing a button on the key fob;
temperature mode for engine starting, the driver can configure the system in such a way that at a certain sub-zero temperature, the engine will start, warm up and stall on its own (ideal for northern regions).

The kgbfx 8 model is also endowed with such functions; car alarms with this index are also designed for automatic engine start settings in winter. The kgbfx 7 alarm, the instructions of which contain detailed steps on how to configure it, also has the function of automatically starting the engine upon a signal from the driver, but its capabilities are less than those of the fx 5.

It is important to remember that each modification of this alarm system is equipped with all the necessary equipment that will be needed to install it on a car.

The KGB FX-7 car alarm model is a new 12-volt system with auto start and feedback. In our country, this brand is represented by MMC. KGB FX-7 is produced in Taiwan - at the same plant where the popular StarLine car alarms are produced. This explains the great similarity of the KGB FX-7 with the Starline B9.

Unlike the popular KGB FX-5 model, the new car alarm has a new original key fob with feedback and a very informative liquid crystal display.

When the key fob receives a return signal from the car, the light signaling of the execution of the sent command is activated.

When the KGB alarm is triggered, the key fob informs the car owner with light and sound signals, including a vibration signal. Now you will never miss an alarm.

For review and comparison, the KGB FX-7 alarm key fobs use a new dynamic radio control code with reliable protection against intelligent hacking based on an interactive algorithm for identifying your key fob and distributing commands to enable or disable the security mode to different buttons. In this case, commands sent from other key fobs and written into memory are duplicated by the key fob with feedback, provided that it is located within the communication range.

System functions

The car alarm has the following options:

giving sound and light signals when one of the sensors is activated and transmitting a message to the control key fob;
turning on panic mode with a button;
blocking the power unit during a break-in attempt;
two-way communication allows you to monitor and control the system using the control key fob (read more about car alarms with feedback);
The car engine lock remains activated even after the alarm is removed;
The Anti-Robbery mode can be turned on with a special button;
When the system starts, all sensors and devices are checked, and any problems are reported on the key fob screen.

Reviews: how to set autostart on a Tomahawk key fob

This is the opinion of motorists about the work of Tomahawk security systems.

Fedor:

I couldn’t figure out what the reason was, the car wouldn’t start from the remote control, but it started normally with the key. I looked through the instructions, searched the forums, replaced the battery with a powerful unit, and now everything is fixed. Even at -30 degrees Celsius I checked - everything works fine.

Maksim:

I bought it because it has automatic engine warming up and you can play with the modes. The car is parked under the entrance in winter and summer. When I leave the apartment, I turn on the autostart, and warm transport is waiting for me below.

Safety precautions

Some nuances when using the alarm system.

The system can be installed on cars with a 12-volt power supply.
If it is necessary to drill the machine body for installation, it is best to clarify this point with the dealer. Otherwise, you may lose your warranty.
Before installation, a test connection is made with all elements activated. This is necessary to identify a possible defect.
The system must be secured only with the fasteners that are included in the kit. The use of third party parts may result in incorrect operation.
Avoid getting water and detergents on the system elements; to do this, installation must be done in places inaccessible to moisture.
If any alarm unit fails, there is no need to try to open it and carry out independent repairs.
Do not use solvents or strong detergents to remove dirt from the surface of the device. It is best to do this with a dry paper napkin.

Autostart button on Tomahawk key fob

On the standard Tomahawk alarm remote control, the role of the start button is played by a key with the image of a key. On most models, adjustment of the element is not required - everything is programmed initially at the factory. The driver just needs to complete the preparation procedure and enter a certain combination.

You can see what the part looks like in the photo.

How to use autorun

To prevent an emergency, the engine starting system is not turned on in the following cases:

ignition on;
the handbrake is not turned on;
the brake pedal is pressed;
the hood is open;
Neutral speed on manual transmission or parking mode on automatic transmission is not enabled.

Auto start limitations:

the number of attempts to start the engine does not exceed four;
if the engine stalls during warm-up, it starts again;
Autostart during cooling works independently of other programs (by time or after a period).

If after 4 attempts the engine does not start , the key fob gives an audible warning and 4 light signals . 60 seconds before the warm-up is completed, the device emits two series of sounds , 4 signals each . The owner of the car is notified about the completion of warming up and stopping the engine by 4 sound and light signals, as well as the message “r00” on the display.

When using automatic start, four rules apply:

The launch occurs regardless of the location and functionality of the main key fob. Therefore, it must be turned off before leaving on a business trip or when parking the car for a long time.
The autorun alarm must be reset before the next cycle.
The error of automatic start by alarm can reach 3 minutes.
If the operating time is set to “unlimited”, the engine will turn off after 30 minutes.

The ability to automatically start the engine is especially important in regions with cold climates. It allows you to comfortably use the car even at temperatures below 25 degrees.

How to enable and disable autorun on Starline? How to set up autostart on the Starline A91 alarm system? Autostart procedure for Starline E91?

How to disable the feature

The user can turn off automatic start using the buttons on the control panel. It is impossible to completely disable the function, since the motor operation algorithms are embedded in the software of the central unit. If problems occur with automatic start, it is recommended to force reset the alarm settings and then reprogram the parameters.

The StarLine A94 alarm system, equipped from the factory with a 2CAN module, is the best price option for cars with digital buses, with the exception of those where the body wiring is based on LIN. But since such cars are in the minority, there is no point in focusing on them. The number “9” in the marking indicates support for A94 autostart, which is implemented using an external power control module. However, it can also be used on cars where autostart does not require duplication of power circuits (the “Start-Stop” button is used or the ignition switch serves as a low-current switch, as on the Renault Megane III).