At night, the likelihood of accidents and emergency situations increases sharply. In addition, not every car is equipped with good optics, which gives the driver additional confidence when driving on the road. In many cases, independent modification of lighting fixtures is required. It provides them with greater practicality and original design. Installing lenses in headlights is the optimal solution for all drivers, without exception. You will learn about all the nuances of work and installation from this article.
Xenon Features
Automobile manufacturers have always strived to reduce the lack of visibility in the dark when driving a car. Therefore, the development of xenon lamps was a real breakthrough in the car market. What is xenon? It is an inert gas. A lamp with such a “filling” has a completely different operating principle compared to a conventional incandescent lamp. Lighting occurs due to the appearance of an electric arc. Special ignition units included in the xenon headlight kit are responsible for its creation. They produce voltage pulses producing a powerful, bright glow.
Now let's figure out what bi-xenon headlights are and what is the difference from xenon. They work on the same principle of illumination, but the bi-xenon performs a dual function and can operate in low and high beam mode. In addition to optical glass and a light reflector, the model is equipped with a movable curtain that allows switching the light flux from near to far and back. In addition, the service life of gas-discharge headlights is 2-3 times longer than halogen ones, and they shine much brighter.
However, the installation of any xenon requires compliance with 3 important factors. The absence of one of them will make the installation of special lenses ineffective. So, the car must be equipped with:
- a headlamp with transparent rather than corrugated glass, because irregularities scatter the light beam, and the xenon beam is much more powerful than a regular halogen.
- headlight washer, because its use will prevent light from scattering in different directions;
- automatic headlight leveling, which ensures their coordinated operation.
Thanks to xenon lamps, driving a car will become safer and will allow you to promptly detect an obstacle and take the necessary measures. The radiation spectrum will become continuous, close to the solar one. In addition, adjusting the headlights will be much easier. A nice bonus is that if the car starts to “bounce” on uneven roads, the headlights do not go out or blink.
Installing halogen lenses in car headlights
In order to carry out this tuning, you must have all the necessary equipment, since it is impossible to carry out this procedure without it. So don't try to do it yourself. Essentially, the installation process can be divided into several stages:
- Disassembling the headlight;
- Removing glass;
- Elimination of possible contamination;
- Lens installation;
- Assembling the headlight to its original position;
You must understand that such serious tuning can only be entrusted to trusted specialists who have a well-deserved reputation. If you are in the city of Yekaterinburg, then you should pay attention to the installation center Svetodiod96, which has proven itself professionally. Having given your preference to this service, you will be pleasantly surprised by the excellent price-quality ratio of the work performed.
Which xenon is better to choose?
Today there are a lot of tempting offers on the car market. However, when making a choice, you should always first pay attention to the manufacturer. The most budget option is considered to be xenon from China (about $40 per set), and the elite category is completed by German manufacturers - Bosch, Osram, Hella (up to $150 per set).
Experienced car owners do not recommend buying cheap "China" cars due to frequent cases of rapid combustion of ignition units, changes in the color of the lamp, or frequent blinking of the light. As an alternative to the “average” one, you should take a closer look at the Korean xenon Sho Me, which is famous for its low defect rates and works properly in all weather conditions. Judging by the reviews, such xenons can remain on a car for about 10 years without any complaints from drivers.
Secondly, it is necessary to take into account the glow temperature (TC). The lowest threshold is 3000 K. The higher this indicator, the shorter the length of the light beam. For example, xenon with TC = 3000 K has a yellow light, while 4300 K is a white soft light, which is considered the most suitable for installation, therefore it is installed on the car at the factory.
Thirdly, we look at power. The most popular setting is 35 W. If the lens (headlight) is designed for this particular power, then 50 W will simply ruin the headlight. It happened that the reflector burned out/cracked from too high temperatures.
Fourthly, there are different types of bi-xenon lenses. They differ in their sizes and generations:
| Name | Peculiarities | Diameter |
| G-1 | The very first lenses were in the shape of a circle. Installed in headlights with H socket. Includes: 2 lenses with illuminated angel eyes decoration, fasteners, 2 lamps. | 80 mm |
| G-3 | The third generation of universal round bi-lenses. Compatible with base types HB4, H1, H7. The set is identical to the previous one. | 110 mm |
| G-5 | Lenses of the smallest diameter. Compatible with most sockets (HB4, H1, H4, H7). Kits may vary. | 64 mm |
Xenon when allowed 2020
Only properly installed xenon headlights are beneficial. Unauthorized installation is punishable by law and for good reason; many, in the name of economy, violate all norms and install xenon themselves. So the punishment for xenon in 2020 is completely justified.
If such a violation is detected, Article 12.5, Part 3 of the Code of Administrative Offenses is applied, providing for imprisonment for a period of six months to a year for violating the operating mode and color of lighting devices. But there is a judicial practice on deprivation of rights for xenon, which was applied until June 2020, a big flaw, when the application of Part 3 of Article 12.5 is unacceptable.
Bi-xenon installation
This is done using tools such as:
- 2 wide blade screwdrivers:
- 1 Phillips screwdriver for disassembling optics;
- 1 Phillips screwdriver for removing the lens;
- fabric gloves;
- pliers.
Preparatory work
High-quality installation of BL in headlights will be ensured by thorough preparation for this procedure. This way you will avoid wasting time when warming up the case. So, preparation requires the following algorithm of actions:
- Using a wide Phillips screwdriver, unscrew the screw that holds the lamp. Set aside the plate with the mount and the lamp structure.
- Determine the type of light bulb base and select the necessary rings (adapters). Try them on the design.
- There is no need to peel off the protective film from the lens glass completely, only at the base.
- There is a TOP mark on the body. Find it and remember that during the disassembly process it should only look up.
We prepare lenses for installation in headlights as follows:
- We remove used lenses and clean their inner surface with a plastic brush. To polish headlights, use a rag with polish. If the product is too dirty, clean it in soapy water and then dry it.
- We remove pipes, plugs, turn signals and other parts of the structure. If there is a bracket holding the glass, we also dismantle it.
- We unscrew the fasteners, remove the rubber cover (if present) protecting the location of the light bulb and remove the retaining spring.
Warming up and disassembling
Heating the substance with a powerful industrial hair dryer in a thermal box will help make the sealant softer and quickly separate the glass from the headlight housing. To make it, we take an ordinary box and put the headlight there. If there are a large number of cracks, seal them with tape. Close the box tightly, insert the hair dryer nozzle into it and turn it on at a power of 250 degrees. Next, you should wear gloves or wrap a towel around your hands to avoid possible burns. We periodically inspect the headlight.
As soon as the housing begins to “diverge,” remove the headlight from the thermal box and place it glass side down. Using a screwdriver, CAREFULLY remove the parts at the sharp edge to prevent chipping. We protect the reflector from contact with sealant.
Mounting and installation of lenses in headlights
Installing lenses in headlights involves performing the following steps:
- Pass the curtain and power control wiring into the hole for the lamp.
- Install the lens into the headlight reflector. On the reverse side, tighten the washer, ring and other fasteners.
- Once tightened, the housing should hold fairly tightly, otherwise tighten the nut.
- Apply a thin layer of sealant along the edges of the joints.
- Press the optics firmly against the body.
We install the BL in the headlights and fix all the fasteners. Leave overnight to dry. Then we install the wiring according to the appropriate diagram.
Xenon Is Allowed Or Not In 2020
But there is a big mistake in the judicial practice of depriving rights for xenon, which was applied until June of the year, when the application of Part 3 of the article is exactly what the Supreme Court pointed out in its next Resolution of the Plenum.
This is also prohibited. In this case, it will be illegal to change the design of the vehicle without the permission of the traffic police (the same paragraph 3). In addition, in order to be able to drive with gas-discharge lamps, the Technical Regulations prescribe the mandatory use of auto corrector and headlight washers. But not all car models have them from the factory. Skip to main content. Hotline Russia: Free consultation: 8 Free consultation Ask a lawyer.
Xenon Is Allowed Or Not In 2020
There was also a stereotype that it was the light bulbs in the yellow glass that spread further through the wall of fog, but in practice this theory has already been refuted. Xenon is increasingly being used in headlights, which produces white light.
But in Russia, the use of such lamps in the mode of fog lighting of roads is prohibited unless there is appropriate permission from the traffic police. For unauthorized use of xenon lamps, the car owner is subject to a significant fine.
We recommend reading: Website of Lists of Houses for Relocation of the Administration of Nyagan for 2020
How to connect bi-xenon lenses
We have already looked at how legal it is to install them, and now we should dwell on the technical intricacies of the process.
If you are going to buy bi-xenon lenses, think in advance whether you will do the installation yourself or entrust this work to specialists. In principle, installing bi-xenon is not difficult. The main thing is to act step by step and strictly adhere to safety rules. The main stages of the process are:
2) Disassembling the modules, during which the reflector must be carefully separated from the top glass. To soften the sealant, it is advisable to use a hair dryer or oven, but under no circumstances use hot water.
3) Installation of the module in a disassembled headlight.
4) Check. Before you proceed to assembling the structure, evaluate the performance and condition of the light bulbs.
5) Assembly. At this stage, the most important thing is to ensure tightness.
6) Connection. Install the high beam relay so that it is never exposed to moisture, even accidentally. Connect the wiring to the battery. Securely fix the bulbs and connect the “angel eyes” (if they are provided by the design of the bi-xenon lens). Connect the wires from the “angel eyes” to the standard dimensions - this is absolutely legal, the main thing is to do everything correctly. Then you can install and connect the ignition units.
7) Installation of headlights in their designated place, final assembly of the system.
If you carry out all the procedures correctly, you can be confident in the reliability and durability of your car's optics, and that it will perfectly cope with its tasks.
Xenon Is Allowed Or Not In 2020
Administrative punishment for xenon is deprivation of rights for xenon for a period of 6 months to 1 year. Xenon fog lights, what's the fine? Is it possible to install xenon in fog lights? Today's article is dedicated to xenon in PTF. Hello to all blog readers.
It’s no secret that unadjusted xenon headlights greatly blind drivers of oncoming vehicles, constantly creating emergency situations on the road. But drivers should not calm down, since the traffic police has adopted an official unambiguous interpretation of this offense. This will certainly be of interest to drivers who are interested in what fine they will have to pay for xenon in a year.
What is the fine for xenon in 2020: Punishment under the new law
There is no new law, but changes have occurred. The Supreme Court recently ruled: based on part 3 of Article 12.5 of the Code of Administrative Offenses, it turns out that drivers are punished for violating the work schedule and color at the same time. Those. Separately, these two points do not entail punishment in the form of deprivation of rights.
Has the fine for xenon been abolished? In fact, it turns out that drivers have the opportunity to challenge the deprivation, but smaller courts are not obliged to obey the Supreme Court; they can consider their decision as advisory.
Masks for lenses
Hoods are the same masks for bi-xenon lenses. Serve solely as decoration. The main task is to close the inside of the bimodule so that the reflector is not visible. Masks are also used as decoration or daytime running lights. For this, hoods with angel eyes are installed; this adds an aesthetic appearance to the car and can also be used as daytime running lights. Hoods are divided in the same way as lenses into sizes 1.8, 2.0, 2.5, 3.0″. That is, each lens uses its own proportional mask. But, it is possible to install hoods for 3.0″ lenses on 2.5″ lenses using adapter rings.
Is bi-xenon allowed or not in 2020?
And for xenon headlights, the marking may be as follows: If the marking contains letters, for example, HСR, then only halogen lamps are installed in the headlights - in this case, the use of xenon lamps is already prohibited.
- The latter, in fact, are ordinary incandescent lamps, but with improved light characteristics.
- They use a tungsten filament as a light source, which heats up under voltage and begins to glow.
- A halogen lamp shines worse and worse over time.
- The reason lies in the fact that tungsten gradually evaporates and settles on the inner surface of the flask.
- The second drawback of such lamps is their rather low reliability.
- When driving on bad roads, there is a high probability that the spiral will break. The spiral, which is the light source, is fixed motionless, so the optimal design of the lens and reflector is quite easy to calculate.
