Do-it-yourself automatic transmission oil change in a Chevrolet Aveo

Do-it-yourself automatic transmission oil change on a Chevrolet Aveo Sedan.

Here I want to tell you how you can independently change the oil in an automatic transmission on a Chevrolet Aveo Sedan

Manufacturers recommend changing automatic transmission oil at intervals of 60,000 km. mileage So, open the hood and pull out the dipstick from the automatic transmission.

We will need to remove the pan protection, if any, unscrew three bolts and remove the subframe extension so that it does not interfere with the removal of the automatic transmission pan (seen in the photo).

We clean the pressed surface of the pan and the drain plug with a brush, then unscrew it and drain the oil.

After the oil has drained, screw the plug into place and unscrew all the bolts around the perimeter of the automatic transmission pan.

We remove the pan, drain the remaining oil from it, remove the old gasket and thoroughly wash everything with gasoline or an aerosol cleaner.

Now unscrew the three screws and remove the oil filter.

We take a new filter and install it in place.

On a cleanly washed pallet, do not forget to install the magnets in their places and the pallet gasket. We clean and degrease the automatic transmission pressing surface, then put the pan in place and screw it on.

Using a small funnel, pour new oil through the hole for installing the dipstick. You can safely fill in two liters of oil, then you need to get into the car and change all the gears with the gear shift knob on the engine not running. Then add another liter of oil and start the engine. Now you need to check the level with the engine running and the automatic transmission in park.

After which we again briefly shift all gears with the engine running and set the lever in position P. Warm up the engine to operating temperature, gradually add oil to the hot level on the dipstick of the automatic gearbox. Then we need to check the pan we installed for oil leaks; if everything is in order, you can put the extension and crankcase protection in place.

In this article with a photo report, you saw how you can change the automatic transmission oil on a Chevrolet Aveo Sedan with your own hands.

Checking and changing the oil in the Chevrolet Aveo new T300 gearbox

This box was installed on front-wheel drive vehicles with an engine capacity of up to 2.4 liters.
The manufacturer advises changing the oil in the car’s automatic transmission after a mileage of 150,000 kilometers. But this figure is taken from calculations of normal operating conditions. Russian roads and climate are not normal conditions. And many novice drivers who do not know how to handle a car in the cold season, with an automatic instead of a manual, turn these conditions into extreme ones.

In extreme conditions, it is recommended to change the oil every 70,000 kilometers, making a complete change of lubricant. I recommend performing a partial oil change after a mileage of 30,000 kilometers.

Attention! Check the lubricant level in the Aveo T300 automatic transmission after a run of 10,000 kilometers. And along with the level, do not forget to look at the quality and color of the oil. If the oil in the automatic transmission has darkened and you see foreign impurities in it, then urgently change the lubricant to prevent damage to the Aveo T300 automatic transmission.

If you haven't changed the oil and when driving you hear:

noises in automatic transmission;
pushes and jerks;
vibration of the machine when the car is idling

Do-it-yourself complete and partial oil change in a Chevrolet Cruze automatic transmission

First of all, replace the lubricant. All these signs of bad oil should disappear. If they remain, then take the car to a service center for diagnostics.

Fill the Chevrolet Aveo T300 automatic transmission only with original oil. The Aveo T300 automatic machine is not as afraid of mixing liquids as it is of dirty waste.

Driving for a long time during testing will cause the filter device to become clogged, and the lubricant will no longer be able to perform its functions.

The lubricant will overheat and heat up the mechanical parts. The latter will be subject to rapid wear.

Attention! When buying oil, do not forget about the filter device. You must replace it along with the lubricating fluid, otherwise there is no point in changing the transmission fluid.

Original oil

To replace the lubricant, always use only original oil. For the Aveo T300 gearbox, any oil with the Dexron VI standard is original. This is a completely synthetic fluid. For a partial replacement, 4.5 liters is enough, and for a complete replacement, 8 liters.

Analogs

The following analogues are suitable for this gearbox if you cannot find original oil in your city:

Havoline ATF Dexron VI;
SK Corporation Dexron VI;
XunDong ATF Dexron VI.

Reasons why automatic transmission oil foams and what the driver should do

The manufacturer strictly prohibits the use of oils with a standard lower than that described.

Checking the level

The Aveo T300 automatic transmission does not have a dipstick. Therefore, you will not be able to check the level in the usual way. But for checking, a special hole is built into the box to check the oil level.

Another difference from other gearboxes is that the automatic transmission cannot be warmed up to 70 degrees. Otherwise, more lubricant will spill out than expected. The steps to check the level will be as follows:

Start the car.
Warm up the automatic transmission to 30 degrees. No more.
Place the Aveo T300 on a flat surface.
Keep the engine running, crawl under the car and unscrew the inspection hole plug.
Place a container under the spilled oil to drain.
If the oil flows in a small stream or drips, then the level is sufficient. If the oil does not pour out at all, then add about a liter.

Don't forget to monitor the quality of the lubricant. If it is black, change the lubricant to a new one.

Before you start replacing the Aveo T300 automatic transmission lubricant, you need to prepare all the materials and tools that may be needed. Therefore, we prepare the following materials:

original lubricant or its equivalent with a tolerance of at least Dexron VI;
filter device under catalog number 213010A. These filters have a double membrane. Some manufacturers say that they can easily last until the fluid is completely replaced. I wouldn't take their word for it if I didn't want my car to start up somewhere in the middle of nowhere;
gasket for the pallet and seals for plugs (it is better to buy repair kit No. 213002 right away);
funnel and hose for filling in new fluid;
rag;
set of sockets and keys;
container for draining lubricant;
carbocleaner for cleaning the pan of Aveo T300.

Reliability of automatic transmission of Niva Chevrolet: maintenance and malfunctions of the machine

Once everything is prepared, you can begin to replace the lubricant yourself.

Write in x, did you change the lubricant on the Aveo automatic transmission yourself? How long did this process take you?

Now let's move on to the topic of replacement itself. Before driving into a pit or lifting the car on a lift, you must warm up the automatic transmission. But not up to 70 degrees again. And only up to 30. The gear selector lever must be moved to the “P” position.

Draining old oil

To drain the waste, take the following steps:

Unscrew the drain plug and place the container.
Lubricant will begin to leak out of the system. Wait until the oil is completely poured into the container.
Remove the pan by unscrewing the mounting bolts. Wear gloves because the oil may be hot.
Remove it with caution so as not to get wet, as it may contain about 1 liter of liquid.
Drain the remaining waste into a container.

Now start washing the pan.

Wash the inside of the pan of the Aveo T300 automatic transmission with carbocleaner. Remove shavings and metal dust from the magnets using a brush or rag. A large amount of chips should make you think about sending the automatic transmission for repair. Perhaps some mechanical parts are already worn out and require urgent repairs.

Read more: Step-by-step replacement of the timing chain on a Mazda 6 instructions photo and video review

After rinsing the tray and cleaning the magnets, leave these parts to dry.

Replacing the filter

Now unscrew the bolts that hold the oil filter and remove it. Install a new one. Never wash the old filter. This will only worsen its throughput.

Do-it-yourself complete and partial automatic transmission oil change

Moreover, this automatic transmission has a double membrane filter. If you don’t want to mess with it, then leave it until the lubricant is completely changed. But I advise changing the filter device after every oil change.

The automatic transmission from the Aveo T300 has a filler hole. It's actually located under the air filter. To get to it, you will need to remove the Aveo T300 air filter.

Put the pan back on and tighten the bolts on it.
Replace the seals on the plugs and tighten them.
After removing this filter, insert one end of the hose into the hole, and insert a funnel into the other end of the hose.
Raise the funnel just above the level of the car's hood and begin pouring in fresh lubricant.
You only need 4 liters. For this type of machine, it will be even better if there is underfilling rather than overfilling.

Check the lubricant level in the Aveo T300 automatic transmission using the method that I wrote about in the block above. Now you know how to do a partial oil change on an Aveo T300 automatic machine.

Write in x how you completely change the oil in the automatic machine. Or do you take it to a service center?

In general, a complete automatic transmission oil change on a Chevrolet Aveo T300 is similar to a partial fluid change. But with one difference. To carry out such a replacement, you will need a partner.

Attention! A complete change of mining is done at a service station using a special high-pressure apparatus. It is used to pump out old oil and fill in new oil. This procedure is called the substitution process.

Steps of the procedure at home or agar:

Repeat all the steps to drain the waste, clean the pan and replace the filter, as described above.
When you need to add new oil, fill it up and call your partner.
Disconnect the return hose from the cooling radiator and insert it into the neck of a five-liter bottle.
Ask your partner to start the Aveo T300 engine.
The used oil will flow into the bottle. At first it will be black. Then it will change color to light.
Shout to your partner to turn off the engine of the Aveo T300.
Add as much oil as was poured into the bottle.
Now tighten the fluid filler plug on the automatic transmission. Reinstall the filter device.

You drive the car and then check the level again. Do not forget to carry out the procedure for adapting the automatic transmission to your driving style. This is necessary so that the car does not jerk or push when starting from a standstill or changing gears. This often happens after adding fresh lubricant.

Write in x, have you already carried out a complete lubricant change in the Aveo T300 automatic transmission?

Conclusion

Do not forget about changing the oil in the automatic transmission of the Aveo T300 vehicle, and about preventive maintenance in the automatic transmission, which must be carried out every year. And, if the car is used in extreme operating conditions, then twice a year. Then the automatic transmission will last not only 100 thousand kilometers without repair, but also all 300 thousand.

If you liked the article, please like and share it on social networks. Write in x what else you would like to know about from our site.

Many novice motorists who have received their first car ask questions about its independent repair and maintenance. Trips to a car repair shop take time and money. Therefore, simple operations that do not require special knowledge and equipment are best carried out at home, in a garage.

We will look at issues related to the automatic transmission of the Chevrolet Aveo T300: what to do if it stops working correctly and how to change the transmission oil in the automatic transmission.

Transmission fluid performs SIX important functions at once in an automatic transmission:

firstly, it lubricates the moving parts of the mechanism, reducing their wear;
secondly, it plays the role of a coolant, removing heat from the gears;
thirdly, it participates in the transmission of torque in the torque converter of the box;
fourthly, it plays the role of friction lubricant, improving the adhesion of mechanisms;
fifthly, it protects gearbox parts from corrosion, performing the functions of an anti-corrosion agent;
and sixthly, it plays the role of “blood” of the mechanism, washing out wear products of gear teeth from the oil lines and leaving them on the oil filter.

A lack of ATF or its contamination leads to a loss of oil pressure in the gearbox, which causes overheating of the mechanism and accelerates wear of parts. This can be expressed in problems switching transmission modes, extraneous noise in the transmission, slipping and loss of traction of the car.

Changing the oil in a Chevrolet Aveo automatic transmission

It’s hard to disagree that thanks to the automatic transmission, driving the car becomes much more convenient. But changing the oil in an Aveo automatic transmission at a service station is not a cheap pleasure. Some car mechanics refuse such work because they consider it very responsible and difficult. On the other hand, many car enthusiasts successfully carry out this procedure on their own. Timely oil renewal, as well as careful treatment of the gearbox, can significantly extend the service life of this unit.

Do-it-yourself oil change in a Chevrolet Aveo automatic transmission

So, let's look at how the oil is changed in a Chevrolet Aveo automatic transmission under normal, non-professional conditions.

According to the manufacturer's advice, the oil in an automatic transmission should be changed every 60 thousand kilometers. Well, first you need to open the hood slightly and remove a special dipstick from the gearbox.

If you want to change the oil in a Chevrolet Aveo automatic transmission with us, please follow the link.

What kind of oil should be poured into the Chevrolet Aveo T300 automatic transmission?

Petro-Canada - DEXRON-VI ATF
ConocoPhillips Company - DEXRON-VI ATF
ExxonMobil Corporation - Mobil DEXRON-VI ATF
SK Corporation - ZIC DEXRON-VI
Kendall Motor Oil Company - DEXRON-VI ATF
S-Oil Corporation - SSU ATF DEXRON-VI
Chevron Corporation - Chevron ATF DEXRON-VI
Havoline ATF DEXRON-VI
Sinopec Corporation - XunDong ATF VI
Petronas - PETRONAS TUTELA Transmission DEXRON-VI ATF.

The car enthusiast must dismantle the protective part of the pan (of course, if it is present), unscrew the bolts (3 pieces), remove the stretcher from the subframe - it interferes with disassembling the transmission pan.

We use a brush to clean the surface of the pan that is pressed, as well as the plug that closes the drain, then twist it and wait for the used oil to pour out.

After waiting for the fluid to drain, close the hole with a plug, and then unscrew the bolts located at the edges of the transmission pan.

Now the pan can be easily removed, and you can easily remove any remaining oil from it. We remove the gasket and carefully wash everything (for example, with gasoline or another cleaner).

We unscrew the bolts that hold the oil filter (usually there are three of them), and then dismantle it.

We install a new filter in place of the old one.

Now on the cleaned surface of the pallet we install magnets in the appropriate areas, as well as a gasket. Then the pressure part of the gearbox should be degreased and also cleaned. Having completed these manipulations, we return the removed parts to their places.

Using a special neck, fill in the purchased lubricant (the hole into which the dipstick is placed). The volume of oil poured should be approximately 2 liters, then you should alternate gears without starting the engine. Then add one liter of lubricant and start the engine. We put the automatic transmission into park and check the level with the engine running.

With slight delays, we change gears (while the engine is running), fix the lever in the “P” state.

At the last stage, you should warm up the engine to the operating, standard level. Gradually add oil on the gearbox dipstick. We check the fixed pan for fluid leaks; if there are no problems, we return the elements that protect the crankcase and, accordingly, the extension to their places.

So, now you know how to change the oil in the automatic transmission of a Chevrolet Aveo T300 .

Practical advice on choosing oil in an automatic transmission Chevrolet Aveo T300

Fill the Chevrolet Aveo T300 automatic transmission only with original oil. The Aveo T300 automatic machine is not as afraid of mixing liquids as it is of dirty waste. Driving for a long time during testing will cause the filter device to become clogged, and the lubricant will no longer be able to perform its functions. The lubricant will overheat and heat up the mechanical parts. The latter will be subject to rapid wear.

Attention! When buying oil, do not forget about the filter device. You must replace it along with the lubricating fluid, otherwise there is no point in changing the transmission fluid.

Original oil

To replace the lubricant, always use only original oil. For the Aveo T300 gearbox, any oil with the Dexron VI standard is original. This is a completely synthetic fluid. For a partial replacement, 4.5 liters is enough, and for a complete replacement, 8 liters.

Analogs

The following analogues are suitable for this gearbox if you cannot find original oil in your city:

Havoline ATF Dexron VI;
SK Corporation Dexron VI;
XunDong ATF Dexron VI.

The manufacturer strictly prohibits the use of oils with a standard lower than that described.

Changing the oil in the automatic transmission of a Chevrolet Aveo T300

Chevrolet Aveo T300 is a relatively modern budget car that requires qualified diagnostics. Comprehensive maintenance will save your car from costly repairs. One of the most important procedures affecting the performance of a car is changing the oil in the gearbox. Fortunately, you can do this yourself without resorting to the help of dealerships. Let us consider in detail how, using the example of a Chevrolet Aveo T300 with an automatic transmission, you can change the oil yourself.

How often do you change the oil?

In fact, gear oil is not the most common consumable item. The manufacturer generally recommends changing the fluid every 150 thousand kilometers, and such mileage, as you know, is very rare for modern cars. And yet, many owners are not going to sell their car and prefer to repair it themselves, without any warranty.

You should not pay attention to the official regulations of 150 thousand km. For better safety and reliability, the gearbox oil must be changed every 30-40 thousand kilometers. This is normal, especially since the procedure is carried out without any devices or other expensive instruments. This is called a partial oil change. It is less effective than full service using diagnostic equipment. And yet, such a procedure is enough to ensure a long service life of the Chevrolet Aveo T300 transmission.

Procedure for partial/complex replacement

Start the engine, warm up the oil in the box
Drive the car onto an overpass or inspection hole, apply the parking brake, move the transmission selector to position P
Then, while holding the accelerator pressed, turn on different gearbox speeds several times, starting with P (parking) and ending with D (forward). In each position, hold at intervals of 2-3 seconds. After this, the gearbox selector must be moved to “Neutral” (N). Release the brake pedal and turn off the engine. Then remove the engine crankcase protection to gain access to the oil filter. It may be in poor condition and will need to be replaced
Loosen the drain plug to observe the fluid level
Unscrew this same plug all the way
Start the engine and leave it idling. At this moment, old liquid will begin to flow out of the drain hole into a pre-prepared pan.
After the liquid has drained, you need to check how dirty it is. Perhaps there are traces of metal shavings - a clear sign of mechanical wear of the internal components of the automatic transmission. In this case, changing the oil is a primary and urgent task. Most likely, a complex flush using a diagnostic tool and flushing fluid may be required here.
Let's pay attention to the condition of the drain plug before screwing it back in after adding oil. There is an o-ring in the plug, which will probably also have to be replaced, like the oil filter
Tighten the inspection hole with a plug using a wrench with a force of 12 Nm.
Pour new oil into the filler hole where the dipstick is located. It is necessary to fill in exactly as much liquid as the amount of old oil that has spilled out. Typically this is about 7.7 liters.
After adding new oil, tighten the plug, turn on the engine and let it idle for 5 minutes. Check the oil level with a dipstick - if the level is normal (not above or below the Max mark), then the oil change process has been completed successfully.

Materials for complex replacement in automatic transmissions

Before you start replacing the Aveo T300 automatic transmission lubricant, you need to prepare all the materials and tools that may be needed. Therefore, we prepare the following materials:

original lubricant or its equivalent with a tolerance of at least Dexron VI;
filter device under catalog number 213010A. These filters have a double membrane. Some manufacturers say that they can easily last until the fluid is completely replaced. I wouldn't take their word for it if I didn't want my car to start up somewhere in the middle of nowhere;
gasket for the pallet and seals for plugs (it is better to buy repair kit No. 213002 right away);
funnel and hose for filling in new fluid;
rag;
set of sockets and keys;
container for draining lubricant;
carbocleaner for cleaning the pan of Aveo T300.

Once everything is prepared, you can begin to replace the lubricant yourself.

Write in the comments, did you change the lubricant on the Aveo automatic transmission yourself? How long did this process take you?

How to check the level and change the oil in the automatic transmission of a Chevrolet Aveo car

Chevrolet Aveo cars are very popular in Russia and abroad. This is an inexpensive but practical car with decent technical characteristics. If you have chosen a version with an automatic transmission, you should know about the nuances of operating the automatic transmission, checking the lubricant level and the features of replacing it as necessary. The procedure for changing the automatic transmission oil in a Chevrolet Aveo T300 takes a little time, but requires mandatory adherence to certain rules and recommendations. The main ones are the frequency of replacement and the correct selection of new lubricant.

How to check the Aveo automatic transmission oil level

Checking the quality and level of the oil is carried out on an engine warmed up to 85 °C through control plug 3 located on the automatic transmission crankcase. In this case, the gear selector must be in position P. If oil does not start to drip or flow from the control hole, add it through the breather plug 1.

Layout of the breather (1) and control plug (3)

The check is carried out after a short trip with shifting through the entire gear range. Use a key of 11 to unscrew the control plug, the oil should flow out, and the engine should run during the check.

. After checking the level and tightening the plug, add about 200-300 g of oil into the breather.

The condition of the oil is judged by its smell, appearance and fluidity. If the oil smells burnt or cloudy

and with inclusions of solid particles, it definitely needs to be replaced.
Experts recommend replacing the filter only after a major overhaul of the box, since this is only possible with complete disassembly. The serial number of the original filter is No. 213010A
.

Replacement frequency

Engine oil, like gearbox oil, has its own expiration date. This is the period of time during which the lubricating fluid retains its operational and physicochemical properties. Typically, engine oil is changed several times more often than transmission oil. This is due to the severity of the conditions in which the oils are located and the intensity of their work. If we talk about when to change the oil in the automatic transmission of a Chevrolet Aveo, then you need to look at the operating manual. The automaker recommends draining and updating the transmission lubricant every 60 thousand kilometers traveled.

But in reality this may happen somewhat more often. The more intensely you use your car, the faster the oil in the gearbox wears out. Severe conditions require more careful monitoring of the fluid condition and a shorter period between changes. That’s why some car owners have to drain and fill the automatic transmission with oil every 30–40 thousand kilometers.

Transmission oil change interval

Russian roads and climate are not normal conditions. And many novice drivers who do not know how to handle a car in the cold season, with an automatic instead of a manual, turn these conditions into extreme ones.

Attention! Check the lubricant level in the Aveo T300 automatic transmission after a run of 10,000 kilometers. And along with the level, do not forget to look at the quality and color of the oil. If the oil in the automatic transmission has darkened and you see foreign impurities in it, then urgently change the lubricant to prevent damage to the Aveo T300 automatic transmission.

If you haven't changed the oil and when driving you hear:

noises in automatic transmission;
pushes and jerks;
vibration of the machine when the car is idling

First of all, replace the lubricant. All these signs of bad oil should disappear. If they remain, then take the car to a service center for diagnostics.

Oil selection

To purchase new gearbox oil for your Chevrolet Aveo, use the official operating manual for the car. It states that the T300 uses motor oil with technical characteristics designated Dexron VI. This is a transmission oil that is optimal in its technical and physical-chemical properties, suitable for automatic transmissions. Oils with appropriate characteristics and markings are produced by different companies. Therefore, start from the markings on the containers. Among the most preferred manufacturers are the following:

Petro Canada;
S-Oil;
Havoline;
SK;
ConocoPhillips;
Exxon Mobile;
Kendall;
Chevron;
Petronas;
Sinopec.

Each of the presented oils with the corresponding characteristics is suitable for Chevrolet Aveo cars, which are equipped with an automatic transmission. Use only high-quality oil that has all certificates and confirmations of authenticity. There are also fakes on the market that can damage the automatic transmission.

Preparatory activities

In order for the gearbox oil change to be successful and for you to do the job correctly yourself, preparation and a set of certain tools are required. For a Chevrolet Aveo with an automatic transmission, when changing the lubricant, you need to take:

set of tools;
several keys and heads;
an empty container for old gear oil;
metal brush;
new gasket for the pan;
new oil filter;
degreasers;
dry rags;
new transmission fluid;
special neck for filling oil.

This is a standard set of tools and materials that will come in handy when changing transmission oil on an Aveo.

Checking status

To assess the current condition of the transmission fluid, you need to check how much oil is currently in the Aveo box. Assess the available volume in the gearbox, the level and take a closer look at the fluid itself. It’s not difficult to figure out how to check the oil level. For this purpose, there is a special automatic transmission dipstick under the hood. It is used in the same way as an engine oil dipstick. Therefore, keep a dry cloth at hand and navigate by o and “Max” on the long dipstick of the Chevrolet Aveo gearbox.

If the dipstick shows a deviation from the normal level, do not rush to simply add a little fresh oil. Take a white cloth and place a few drops of liquid on it. If it differs in color from fresh oil, has inclusions or particles of debris, dirt or metal dust, this indicates wear and contamination. It is better to completely change the transmission fluid. First, it would be useful to find out why the oil in the Chevrolet Aveo automatic transmission ran out ahead of time, and whether there are any leaks or any breakdowns in the automatic transmission.

How to change the oil in an Aveo gearbox - instructions

As the manufacturer of the Chevrolet Aveo indicated, the oil in a manual transmission cannot be replaced, i.e. it has a lifetime interval. However, it is recommended to regularly monitor the level of transmission oil in it. It should only be changed if the gearbox is repaired.

As Aveo operating experience shows, with a mileage of 80-100 thousand km, there may come a time when the gears begin to engage dryly, a small crunching sound appears, a hum occurs while driving, etc.

According to experts, this is due to the fact that the manufacturer does not fill the box with expensive high-quality oil, which has a lifetime interval of use, but fills in cheap semi-synthetic, which during use absorbs fine abrasive, metal oxide, formed from friction, which as a result worsens the operation of its components and details.

A simple change of transmission oil helps solve all these problems (